SaVi H2O
IMPROVING THE QUALITY OF WATER

Products

SaVi H2O Filter

$350.00  /  0.00893 ɃAdd to cart

Specifications

  • Material: Food grade polyethylene, ensures clean water quality
  • Outside diameter: 3″ (76.2mm)
  • Length: 12″ (304.8mm)
  • 3/8″ compression
  • Pressure: 300 psi (21 bars)

Operating Limits

  • Maximum operating temperature: 113°F (45°C)
  • Maximum operating pressure: 300 psi (21 bars)
  • Maximum feed flow rate: 1.3 gpm (5 lpm)
  • Power consumption: 10 Watt
  • Voltage: 100-240 VAC
  • Frequency: 50/60 Hz
  • PEMF: Ultra Low Frequency
  • Program duration: continuous

Specifications

  • Material: Food grade polyethylene, ensures clean water quality
  • Outside diameter: 3″ (76.2mm)
  • Length: 12″ (304.8mm)
  • 3/8″ compression
  • Pressure: 300 psi (21 bars)

Operating Limits

  • Maximum operating temperature: 113°F (45°C)
  • Maximum operating pressure: 300 psi (21 bars)
  • Maximum feed flow rate: 1.3 gpm (5 lpm)
  • Power consumption: 10 Watt
  • Voltage: 100-240 VAC
  • Frequency: 50/60 Hz
  • PEMF: Ultra Low Frequency
  • Program duration: continuous

Installation

  • Package includes filter, adhesive back supports, zip ties, 3/8″ tube, and power supply.

Installation Steps

  • Shut off the cold-water supply. Ensure the set-up will be close to an outlet to connect the power supply, and valves to connect the tubes.
  • Place the SaVi H2O filter under the counter: Insert the two adhesive supports vertically. Distance them about 6-9 inches apart. Insert each zip tie horizontally through the adhesive back support holes. Secure the zip ties around the filter to hold in place.
  • Disconnect the cold-water supply tube (the faucet’s tube) from the shut-off valve.
  • Connect that faucet tube to the output (top fitting) on the SaVi unit.
  • Connect one end of the 3/8″ tube (included in the package) to the shut-off valve and the other end to the input (bottom fitting) on the SaVi unit.
  • Review the connections and ensure they are secure. Turn the water supply back on to check for leaks. Note: Connections should be tightened securely, but not overtightened. If leaks persist, turn the water supply back off, disconnect, and apply a sealant to the leaking joint. Not all piping arrangements are the same. If supplied parts are not enough to make the appropriate connections, obtain what is needed at the local hardware or plumbing supply store.
  • Connect the filter to the power supply (included in the package) and then plug it into an outlet.
  • Turn on the faucet. Water will shoot out black at first due to carbon fines; this is normal. Let the water run for at least 5 minutes to activate the filter fully.

SaVi H2O Link

$375.00  /  0.00956 ɃAdd to cart

Specifications

  • Material: Stainless Steel
  • 3/8″ compression
  • Weight: 8.5oz (0.24kg)
  • Length: 5.5″ (140mm)
  • Diameter: 2.0″ (50mm)

Operating Limits

  • Maximum operating pressure: 150 psi
  • Power consumption: max 10 Watt
  • Voltage: 100-240 VAC
  • Frequency: 50/60 Hz
  • PEMF: Ultra Low Frequency
  • Program duration: continuous

Specifications

  • Material: Stainless Steel
  • 3/8″ compression
  • Weight: 8.5oz (0.24kg)
  • Length: 5.5″ (140mm)
  • Diameter: 2.0″ (50mm)

Operating Limits

  • Maximum operating pressure: 150 psi
  • Power consumption: max 10 Watt
  • Voltage: 100-240 VAC
  • Frequency: 50/60 Hz
  • PEMF: Ultra Low Frequency
  • Program duration: continuous

Installation for under the sink

  • Shut off the cold-water supply for the water from the faucet.
  • Ensure there is an outlet for the power supply near the set up for the Link.
  • Disconnect the cold-water supply tube (the faucet’s tube) from the shut-off valve.
  • Connect that faucet tube to the output side of the link.
  • Connect the Link to the existing filter or SaVi H2O filter.
  • Review the connections and ensure they are secure. Turn the water supply back on to check for leaks. Note: Connections should be tightened securely, but not overtightened. If leaks persist, turn the water supply back off, disconnect, and apply a sealant to the leaking joint. Not all piping arrangements are the same. If supplied parts are not enough to make the appropriate connections, obtain what is needed at the local hardware or plumbing supply store.
  • Connect the filter to the power supply (included in the package) and then plug it into an outlet.

Installation for the refrigerator

  • Shut off the water supply for the refrigerator.
  • Ensure there is an outlet for the power supply near the set up for the Link.
  • Disconnect the water supply tube (if there is already an existent filter). Or cut the tube in half (if there is no existing filter). Insert the side of the tube closest to the water supply into the input fitting of the SaVi Link.
  • Insert the other side of the tube, closest to the refrigerator, to the output fitting of SaVi Link.
  • Turn the water supply back on to check for leaks. Note: If leaks are present, turn the water supply back off, disconnect, and apply a sealant to the leaking joint. Not all piping arrangements are the same. If supplied parts are not enough to make the appropriate connections, obtain what is needed at the local hardware or plumbing supply store. 
  • Lastly, connect the unit to the power supply (included in the package) and then plug it into an outlet.

SaVi H2O Bamboo Bottle

$35.00  /  0.00089 ɃAdd to cart

Specifications

  • Volume of Water: 15oz
  • Exterior Material: 100% organic bamboo
  • Interior Material: BPA free stainless-steel
  • Insulated: Keeps beverages hot for 12 hours and cold drinks for 24 hours
  • Accessories: Includes a built-in tea infuser
  • Washing: Hand wash recommended
  • Package Description: Boxed
  • Weight: 0.81lbs
  • Dimensions: 8.125″

Specifications

  • Volume of Water: 15oz
  • Exterior Material: 100% organic bamboo
  • Interior Material: BPA free stainless-steel
  • Insulated: Keeps beverages hot for 12 hours and cold drinks for 24 hours
  • Accessories: Includes a built-in tea infuser
  • Washing: Hand wash recommended
  • Package Description: Boxed
  • Weight: 0.81lbs
  • Dimensions: 8.125″

Installation Video

Limited Warranty

SaVi H2O unit is designed for use on potable systems only. Its effectiveness may be reduced in areas where municipally treated water has chemicals such as polyphosphates to alleviate water problems caused by high iron content. Do not use this unit in water supplies that may reach pressures over the recommended use stated on the instructions. The manufacturer warrants this product to be free from defects in materials and workmanship when installed, operated, and maintained in the manner instructed, for a period of one year from date of purchase. The warranty is limited to the repair or replacement of any unit that fails to perform due to faulty materials or workmanship during the warranty period. To qualify for this warranty, the unit must be maintained and replaced as stated in the instructions. Save your receipt. The manufacturer is not responsible for any damages occurring during the misuse of this product.

Copyright © 2020 – 2021 BlueGreen Innovation LLC. All Rights Reserved.